Pac OS-4 Manuel d'utilisateur télécharger pdf (Page 3)

Pacic Accessory Corporation - Santa Ana, CA 92705

[email protected] • Voice: 866-931-8021 • Fax: 714-835-3233 • www.pac-audio.com

Page 3

09-14-09

• To activate the XM controls press and hold the “Source” button until a chime is heard. The Driver Information

Center (DIC) in the instrument cluster will display “XM Control On”.

• Arrow up moves forward through the channels. The channel name will be displayed on the DIC.

• Arrow down moves backwards through the channels. The channel name will be displayed on the DIC.

• To store a preset, rst choose the preset location by pressing the “Play” button repeatedly. The DIC will display

the XM preset locations. When the desired preset location is displayed, tune to the desired station, then press and

hold the “Play” button to store

• To recall a preset simply press the “Play” button repeatedly until the desired preset is displayed.

• To de-activate the XM controls press and release the “Source” button

PLEASE NOTE: You MUST be installing an aftermarket radio that is equipped with an auxiliary input

to be able to retain the factory XM audio. If the vehicle is equipped with steering wheel controls other

than the ones pictured to the right the OS-4 will not be able to control the factory XM tuner as the

required buttons are not present.

Using the Rear Seat Audio Controls

Turns the

Rear Seat

Controls On

or Off

Change between

Factory XM tuner

and Dual Zone

Radio Source

Controls the

Radio as

Programmed

by the SWC

interface (Mapped

to the Arrow

and Bar Button)

Controls the

Radio as

Programmed

by the SWC

interface (Mapped

to the Arrow

Down Button)

Controls the

Radio as

Programmed

by the SWC

interface (Mapped

to the Arrow

Up Button)

XM 16

Turns the

Rear Seat

Controls On

or Off

Change between

Factory XM tuner

and Dual Zone

Radio Source

Scrolls through

Presets 1-6

Seek to the

Factory XM

Tuner Station

Seek to the

Factory XM

Tuner Station

Using the Radios Dual Zone Source Using the Factory XM Radio Tuner

• Press the power button to turn the RSE Controls on. When Radio is displayed on the RSE

Controls, the aftermarket radios rear speaker output will be heard through the headphone

jacks. Putting the aftermarket radio into dual zone mode should change the output level

of the rear speakers to a xed level. This allows precise user adjustment from the level

knobs on the RSE Controls (refer to aftermarket radio owners manual for model specic

dual zone operation).

• The seek arrows and PROG button will control the radio as programmed by the SWC

interface. These buttons are mapped to the SWC buttons as stated above.

• Pressing the SRCE button will toggle between the Factory XM tuner and the Radio as the

RSE source. Pressing the power button will turn the RSE Controls off as well as turning

the key off. The seek arrows and PROG button will continue to operate as stated (with the

exception of SRCE which has no function) when the Rear Seat Controls are turned off.

• Press the power button to turn the RSE Controls on. If Radio is displayed press the

SRCE button to select factory XM tuner mode. When XM followed by the channel number

is displayed factory XM tuner audio will be heard through the headphone jacks.

• The Seek arrows will control the factory XM radio tuner and select the desired station.

• The PROG button will scroll through Presets 1-6

• Pressing the SRCE button will toggle between the Factory XM tuner and Radio as

the RSE source. Pressing the power button or turning the key off will turn off the RSE

Controls.

• The factory XM tuner must remain serviced to take advantage of this feature. Visit www.

xmradio.com for a complete up-to-date channel listing and service options.

• In order for the RSE controls to properly work the XM tuner, the front XM controls must

be set to off.

OnStar Level Control for Vehicles without SWC Buttons

Using the Factory XM Radio Tuner With the Steering Wheel Controls

SRCE

Press & release to

recall a preset.

Press & hold to store

a preset.

Moves back

through the XM

channels

Moves forward

through the XM

channels

Press & hold to

enable XM controls.

Press & release to

disable XM controls

Factory XM Controls

Volume Up

Volume Down

Installation Notes

1. When the interface is connected to the vehicle for the rst time the car must be running so all vehicle features are recognized by the interface. Once the

interface has been plugged in for the rst time it is necessary to shut the vehicle off and let it sit for at least 5 minutes. Once the vehicle is started again the

XM tuner will be recognized by the OS-4.

2. DO NOT cut the Brown loop on the SWC interface connector. Program the radio specic SWC Interface for version #2.

3. When the Rear Seat Audio jacks are activated in any vehicle OTHER than the Cadillac Escalade or a UQA amplied vehicle the rear speakers will mute.

4. The headphone jacks will play the rear zone source selected by the head unit (refer to the new radios instruction

manual for details on this feature if equipped). Maximize the rear zone volume level (this will reduce unwanted noise).

During an OnStar call the front speakers play OnStar, the rear speakers are muted and the headphones will continue

to play the rear zone audio source.

5. Using the Center and Sub cable for factory reverse camera retention.

• With the supplied brown connector NOT attached to the vehicles brown radio connector: lift the upper and

lower locking tabs near the wire insertion part of the supplied brown connector which houses the center and

sub RCA cables.

• Depress the silver exposed locking tabs on which ever RCA connector (center or sub) is not being used during

this installation.

• After removing both shield (black) and center conductor (red or white) pins - re-insert as follows (see image

aside).

• Pin 6 is the camera+ signal and Pin 7 is the camera- signal. After inserting the pins clasp the locking tab back

down to lock the moved pins into place.

• Fit the modied brown connector into the vehicles brown connector and plug the moved RCA cable into the

aftermarket radios camera input (mark this RCA cable for future reference).

• Use the supplied reverse output wire (green wire in OS-NAV connector) for automatic switching when the

vehicle is put into reverse.

12345678

1112 10 9

916

Center and Sub

Brown Connector (supplied

with interface)

3: Center +

4: Sub +

6: Camera +

7: Camera -

11: Center -

12: Sub -

101112131415

Wire side view

6. DTS, Equinox, Torrent and Vue Installation Notes:

If the vehicle is equipped with a factory amplier other than a Bose amplier and OnStar audio is not heard

during operation the Black/White wire located in the OS-GMLAN29 harness needs to be cut in half and insolated

at both ends (c2 vehicle (16pin) connector pin 8) .

Radio

1 2 3 4

Commentaires sur ces manuels

Pas de commentaire

Pac OS-4 Manuel d'utilisateur Page 3

Commentaires sur ces manuels